- Pages:
- 1
- 2
| question about altima motor in a s13 | |
|---|---|
| Topic Started: Nov 26 2010, 09:51 PM (429 Views) | |
| 1991se240sx | Nov 26 2010, 09:51 PM Post #1 |
|
So as the title states, would a altima ka24de motor work in a s13? Would I have to swapp over sensors or dizzys or anything like that? Reason I ask is bcuz I need a ka, and only oness I can find are for altimas. Thanx guys later |
 |
 
|
| Troskinatior | Nov 27 2010, 01:21 AM Post #2 |
Fap-Master Fap
|
Im 95% sure you cant since its fwd and all |
|
|
|
| 1991se240sx | Nov 27 2010, 06:44 AM Post #3 |
|
Seriously? Bcuz its the same motor basically sideways? Really isn't much diff then the 350 swap in a fiero ( like evrybody is doin wit those) bcuz they turn a RWD motor sideways. I dnt really see much of a diff between the motor fittin or not, its the same motor technically and isn't seperated by codes lke a b18c1 vs a b18c5 or whatevr, they are botth just ka24de's |
|
|
|
| Kevin | Nov 27 2010, 10:48 AM Post #4 |
Horsedick.MPEG
|
Its 100% completely different. Block design is different with motor mount points right on the front and rear of the block Bell housing bolt locations are not the same The cooliing and oil gallies internal to the block are different The Thermostat and water neck are on the rear of the motor (right above trans) The Throttle body faces the rear of the motor (rear meaning towards the trans The head is different, because the distributor is on the rear of the motor You cannot just bolt it to a KA RWD trans and go.... you would need make a bellhousing, notch the sire wall, and make engine mounts. So yeah the block is different, the head is different, the intake TB is different, the cooling system is different. the ignition system is different. But they use the same spark plugs and injectors. Edited by Kevin, Nov 27 2010, 10:49 AM.
|
|
|
|
| Troskinatior | Nov 27 2010, 07:43 PM Post #5 |
|
Fap-Master Fap
|
I would love to see someone acually put the altima ka in a 240 because it has vvt. Right? |
|
|
|
| Kevin | Nov 27 2010, 07:49 PM Post #6 |
|
Horsedick.MPEG
|
Negative |
|
|
|
| Troskinatior | Nov 27 2010, 07:50 PM Post #7 |
|
Fap-Master Fap
|
I know theres one nissan that has a ka with vvt. Right? |
|
|
|
| Kevin | Nov 27 2010, 07:57 PM Post #8 |
|
Horsedick.MPEG
|
No, no KA had VVT or VVL. The replacement to the KA was the QR series, that has VVT
Edited by Kevin, Nov 27 2010, 07:58 PM.
|
|
|
|
| Troskinatior | Nov 27 2010, 08:31 PM Post #9 |
|
Fap-Master Fap
|
Then whats that lump thingy in the valve cover |
|
|
|
| Kevin | Nov 27 2010, 08:43 PM Post #10 |
|
Horsedick.MPEG
|
No lumpy thing., the timing chain cutout is very close the a 240, but its not the same. Remember people swap altima cams into 240's for performance gains. |
|
|
|
| xFIx Kaos | Jan 17 2011, 01:13 AM Post #11 |
|
yea bump motors dnt even look the same lol |
|
|
|
| wolfe215 | Jan 17 2011, 02:28 AM Post #12 |
|
i find ka's for sale all the time |
|
|
|
| 1991se240sx | Jan 20 2011, 02:17 AM Post #13 |
|
yea ive been still searching craigslist and car-parts.com this entire time and still havent had any luck, hate to knock my city but columbus ohio is the worst place to live with a 240. no clowning needed but wut about a frontier KA? its rwd and all rigt?
Edited by 1991se240sx, Jan 20 2011, 03:47 AM.
|
|
|
|
| 1991se240sx | Jan 20 2011, 02:23 AM Post #14 |
|
my car has been garaged for almost a year now, i jus wana slap on this new exhaust and coilovers and wheels and just drive my beast again, taxes are almost here and thatll help but only to an extent. ive seen a few on ebay but 1300 and 1400 is a bit much and im not lookn for a reman right now. im tryna spend 300-400 at the most but not get another shitty ka |
|
|
|
| diggles240 | Jan 20 2011, 09:14 AM Post #15 |
|
Old Fart!
|
So, Scott can't help you find one? If not, and you really can't find one, you need to take a little drive. |
|
|
|
| 1 user reading this topic (1 Guest and 0 Anonymous) | |
| Go to Next Page | |
| « Previous Topic · KA · Next Topic » |
- Pages:
- 1
- 2
2:50 PM May 20